Bi/Bi_2O_3 nanoparticles supported on N-doped reduced graphene oxide for highly efficient CO_2 electroreduction to formate

Electrocatalytic CO_2 reduction(CO_2 ER) into formate is a desirable route to achieve efficient transformation of CO_2 to value-added chemicals,however,it still suffers from limited catalytic activity and poor selectivity.Herein,we develop a hybrid electrocatalyst composed of bismuth and bismuth oxide nanoparticles(NPs) supported on nitrogen-doped reduced graphene oxide(Bi/Bi_2 O_3/NrGO) nanosheets prepared by a combined hydrothermal with calcination treatment.Thanks to the combination of undercoordinated sites and strong synergistic effect between Bi and Bi_2 O_3,Bi/Bi_2 O_3/NrGO-700 hybrid displays a promoted CO2 ER catalytic performance and selectivity for formate production,as featured by a small onset potential of-0.5 V,a high current density of-18 mA/cm~2,the maximum Faradaic efficiency of85% at-0.9 V,and a low Tafel slope of 166 mV/dec.Experimental results reveal that the higher CO_2 ER performance of Bi/Bi_2 O_3/NrGO-700 than that of Bi NPs supported on NrGO(Bi/NrGO) can be due to the partial reduction of Bi_2 O_3 NPs into Bi,which significantly increases undercoordinated active sites on Bi NPs surface,thus boosting its CO_2 ER performance.Furthermore,a two-electrode device with Ir/C anode and Bi/Bi_2 O_3/NrGO-700 cathode could be integrated with two alkaline batteries or a planar solar cell to achieve highly active water splitting and CO_2 ER.     

Cooperative effect of Fe and Ti species over Fe–Ti–Ox catalysts on the catalytic hydrolysis performance of hydrogen cyanide

FeO_x, TiO₂, and Fe–Ti–O_x catalysts were synthesized and used in the catalytic hydrolysis of hydrogen cyanide (HCN). Nearly 100% HCN conversion was achieved at 250 °C over the Fe–Ti–O_x catalyst. TiO₂ rutile was detected over TiO₂, but not over Fe–Ti–O_x, which suggested that the interaction between Fe and Ti species could inhibit the TiO₂ phase transition. Furthermore, the interaction between Fe and Ti species over Fe–Ti–O_x could promote the selectivity of NH₃ and CO. The mechanism of hydrolysis of HCN over FeO_x, TiO₂, and Fe–Ti–O_x can be given as follows: HCN + H₂O → methanamide → ammonium formate → formic acid → H₂O + CO.     

Effect of spatial configuration on adhesion of 1,2-disubstituted cyclohexane derivatives

Spatial configuration has a significant effect on chemical self-assembly. However, the importance of spatial configuration in supramolecular adhesive materials has been frequently ignored. In this study, the effects of the spatial configuration on cohesion and adhesion were investigated. Owing to the diversities of the chemical structures and assembly patterns, 1,2-disubstituted cyclohexane derivatives were used in this combined experimental and theoretical investigation. The self-sorting assembly of enantiopure isomers improved cohesion but had a negative effect on adhesion. In contrast, racemic mixtures displayed stronger adhesion effects. Moreover, it was proven that the cis-configuration was more favorable for supramolecular adhesion than the trans-counterpart. In addition, the influence of the spatial configuration of 1,2-disubstituted cyclohexane derivatives could be effectively mitigated by hydrogen bond donors or acceptors. The addition of natural acids yielded three-dimensional polymeric networks, in which the spatial configuration was not the decisive factor for supramolecular adhesion.     

3D microgel with extensively adjustable stiffness and homogeneous microstructure for metastasis analysis of solid tumor

3D microgels with various mechanical properties have been important platforms tumor metastasis analysis, and widely adjustable stiffness is crucial for deeper researches. Herein, by mixing biodegradable polylactic acid (PLA) nanofibers in the modified alginate with different concentrations of Ca²⁺, we significantly enhance the stiffness range of microgels while retaining the pore size, which provides bionic microenvironment for tumor analysis. As a proof of concept, we simulated the mechanical characteristics of breast tumors by encapsulating cells in 3D microgels with diverse stiffness, and analyzed cellular behaviors of two typical breast cancer cell lines: MCF-7 and SUM-159. Results showed that with the addition of 2.0% (w/v) PLA short nanofibers, the Young's modulus of modified alginate increased more than three-fold. Besides preserving high survival and proliferation rates, both cells also displayed stronger migration ability in soft microgel spheres, where RT-qPCR analysis revealed the underlying changes at the genetic level. This systematic study demonstrated our method is powerful for creating widely adjustable 3D mechanical microenvironment, and the results of cellular behavior analysis shows its promising application prospects in tumorigenesis and progression.     

Preparation and characterization of functionalized graphene oxide/carbon fiber/epoxy nanocomposites

Graphene oxide (GO) was functionalized using three different diamines, namely ethylenediamine (EDA), 4,4′-diaminodiphenyl sulfone (DDS) and p-phenylenediamine (PPD) to reinforce an epoxy adhesive, with the aim of improving the bonding strength of carbon fiber/epoxy composite. The chemical structure of the functionalized GO (FGO) nanosheets was characterized by elemental analysis, FT-IR and XRD. Hand lay-up, as a simple method, was applied for 3-ply composite fabrication. In the sample preparation, the fiber-to-resin ratio of 40:60 (w:w) and fiber orientations of 0°, 90°, and 0° were used. The GO and FGO nanoparticles were first dispersed in the epoxy resin, and then the GO and FGO reinforced epoxy (GO- or FGO-epoxy) were directly introduced into the carbon fiber layers to improve the mechanical properties. The GO and FGO contents varied in the range of 0.1–0.5 wt%. Results showed that the mechanical properties, in terms of tensile and flexural properties, were mainly dependent on the type of GO functionalization followed by the percentage of modified GO. As a result, both the tensile and flexural strengths are effectively enhanced by the FGOs addition. The tensile and flexural moduli are also increased by the FGO filling in the epoxy resin due to the excellent elastic modulus of FGO. The optimal FGO content for effectively improving the overall composite mechanical performance was found to be 0.3 wt%. Scanning electron microscopy (SEM) revealed that the failure mechanism of carbon fibers pulled out from the epoxy matrix contributed to the enhancement of the mechanical performance of the epoxy. These results show that diamine FGOs can strengthen the interfacial bonding between the carbon fibers and the epoxy adhesive.     

Ultrasound-assisted extraction and properties of polysaccharide from Ginkgo biloba leaves

Response surface methodology (RSM) was used to optimize the ultrasound-assisted extraction conditions of Ginkgo biloba leaves polysaccharide (GBLP). The optimum extraction conditions for the ultrasound-assisted extraction of GBLP were obtained as liquid to material ratio of 30 mL/g, ultrasonic power of 340 W, and extraction time of 50 min. Under these conditions, the yield of GBLP was 5.37 %. Two chemically modified polysaccharides, CM-GBLP and Ac-GBLP, were obtained by carboxymethylation and acetylation of GBLP. The physicochemical properties of these three polysaccharides were comparatively studied and their in vitro antioxidant activities were evaluated comprehensively. The results showed that the solubility of the chemically modified polysaccharides was significantly enhanced and the in vitro antioxidant activity was somewhat improved. This suggests that carboxymethylation and acetylation are effective methods to enhance polysaccharide properties, but the results exhibited some uncontrollability. At the same time, GBLP has also shown high potential for research and application.     

Investigating effect of pH values on CeSiW catalyst for the selective catalytic reduction of NO by NH3

Research on Chemical Intermediates - The effect of different pH values (8, 9, 10 and 11) on the catalytic activity over CeSiW catalysts was investigated for the selective catalytic reduction of NO...     

Recent advances in round-the-clock photocatalytic system: Mechanisms,characterization techniques and applications

Solar energy-driven semiconductor photocatalysis has gathered increasing interest in the field of energy and environmental applications. However, a vital problem that limits its application is that photocatalysis requires a continuous light source to perform redox reaction. The ability of keeping catalytic activity in the dark has been the ultimate goal for the wide application of photocatalysis. More and more efforts have been paid to develop photocatalysts to perform photocatalytic reactions under both light and dark conditions, which is so called “round-the-clock photocatalytic system” (RTCPS). RTCPS with an ability of energy storage can work well under both daytime and nighttime, which widely used in the removal of heavy metal ion, the degradation of organic pollutant, disinfection and hydrogen generation. The important potential of RTCPS necessitate timely reviews of the recent advances to streamline efforts. Thus, this review aimed to summarize the recent advances in RTCPS, including the mechanism, characterization techniques and applications. Moreover, future challenge and research direction on the mechanistic study, material design and potential applications are also discussed.     

Synthesis,structure and electrocatalytic H2-evoluting activity of a dinickel model complex related to the active site of [NiFe]-hydrogenases

Structural and functional biomimicking of the active site of [NiFe]-hydrogenases can provide helpful hints for designing bioinspired catalysts to replace the expensive noble metal catalysts for H₂ generation and uptake. Treatment of dianion [Ni(phma)]²⁻ [H₄phma = N,N'-1,2-phenylenebis(2-mercaptoacetamide)] with [NiCl₂(dppp)] (dppp = bis(diphenylphosphino)propane) yielded a dinickel product [Ni(phma)(μ-S,S')Ni(dppp)] (1) as the model complex relevant to the active site of [NiFe]-H₂ases. The structure of complex 1 has been characterized by single-crystal X-ray analysis. From cyclic voltammetry and controlled potential electrolysis studies, complex 1 was found to be a moderate electrocatalyst for the H₂-evoluting reaction using ClCH₂COOH as the proton source.